Source: https://www.youtube.com/@FixItPhil/videos
2011 Honda Accord Battery Replacement Guide
| How to Change the Car Battery in Your 2011 Honda Accord |
|
Changing the car battery in your 2011 Honda Accord is a relatively straightforward process that you can do yourself with a few tools. Here's a step-by-step guide to help you replace the battery:
|
| Step 1: Pop the Hood and Locate the Battery |
|
Start by popping the hood of your car. You'll find the release latch located just inside the driver's side door near the floor. Pull the latch to release the hood, then reach under the middle of the hood and unlatch the catch by pressing the latch to the right while lifting. Raise the prop rod and insert its end into the matching hole on the underside of the hood.
|
| Step 2: Disconnect the Negative Terminal |
|
Before you start working on the battery, make sure to disconnect the negative terminal first. This is an important safety precaution to reduce the risk of a short circuit. You'll find the negative terminal on the right side of the battery, and it's usually marked with a negative (-) sign or colored black.
|
| Step 3: Loosen the Nut on the Post Clamp |
|
Use a 10mm wrench or socket wrench to loosen the nut on the post clamp by turning it counterclockwise. You don't have to fully remove the nut from the screw, just loosen it enough so that you can lift the clamp off the battery terminal.
|
| Step 4: Remove the Clamp and Cap |
|
Lift the red cap covering the positive terminal, then use the same 10mm wrench or socket wrench to loosen the nut on this clamp as well. Then lift the clamp off and move it to the side.
|
| Step 5: Loosen the Nuts on the Crossbar |
|
Next, loosen the nuts on the crossbar across the top of the battery. You'll need either a deep socket or a manual wrench to loosen these nuts, as a standard 10mm socket bit may not be long enough.
|
| Step 6: Remove the Battery Shield and Old Battery |
|
Once you have about half an inch of wiggle room on both sides, press down on one of the bolts and pull it away from the battery. Then remove the battery shield and lift out the old battery. Be aware that the battery weighs around 35 pounds.
|
| Step 7: Install the New Battery |
|
Carefully place the new battery in the battery tray, making sure the positive post is on the left. Then slide the battery shield over it.
|
| Step 8: Reconnect the Terminals |
|
When reconnecting, start with the positive terminal first. Remove the cap on the post, slide the clamp over it until it's fully seated, and tighten the nut. Then connect the negative terminal by sliding the clamp onto it and tightening the nut until it's secure.
|
| Step 9: Start Up the Car |
|
Finally, start up the car to check that it's running fine. Make sure all lights and accessories are working properly before considering the job complete.
|
| Tips and Recommendations: |
|
* Always disconnect the negative terminal first when removing the battery to reduce the risk of a short circuit.
* Make sure to clean any corrosion off the terminals before reconnecting the new battery.
* Use a high-quality replacement battery that meets or exceeds the manufacturer's specifications.
* Consider using a battery with a higher cold crank amps (CCA) rating for better starting performance in cold weather.
|
| Honda Battery |
| A Honda battery is an automotive battery designed and manufactured by Honda Motor Co., Ltd. for use in their vehicles. |
| Background |
| Honda, a Japanese multinational corporation, has been producing batteries for its vehicles since the 1960s. The company's battery division was established to provide high-quality batteries that meet the specific needs of Honda vehicles. |
| The first Honda battery was introduced in 1962 for use in the Honda T360 mini-truck. Since then, the company has continued to develop and improve its battery technology to keep pace with advancements in automotive engineering. |
| Today, Honda batteries are designed to provide reliable starting power, long battery life, and compatibility with Honda's advanced vehicle systems, including hybrid and electric vehicles. |
2011 Honda Accord Battery Replacement Guide |
|
The 2011 Honda Accord is a reliable vehicle, but like all cars, its battery will eventually need to be replaced. If you're experiencing symptoms such as slow engine crank, dim headlights, or a clicking sound when trying to start the car, it may be time for a new battery.
|
Tools and Materials Needed: |
- New battery (2011 Honda Accord battery type: 51R or 4D)
- Socket wrench or ratchet and socket
- Torque wrench
- Gloves and safety glasses
|
Step-by-Step Instructions: |
- Make sure the car is parked on a level surface and apply the parking brake.
- Locate the battery in the engine compartment. It's on the driver's side, held in place by a bracket.
- Disconnect the negative (black) cable from the battery post. Use a wrench to loosen the nut, then pull the cable off the post.
- Disconnect the positive (red) cable from the battery post. Again, use a wrench to loosen the nut, then pull the cable off the post.
- Remove the bracket that holds the battery in place. Use a socket wrench or ratchet and socket to remove the bolts.
- Carefully lift the old battery out of the compartment.
- Install the new battery, making sure it's securely seated in the compartment.
- Replace the bracket and tighten the bolts securely.
- Reconnect the positive (red) cable to the battery post. Tighten the nut securely.
- Reconnect the negative (black) cable to the battery post. Again, tighten the nut securely.
|
Tips and Precautions: |
- Make sure to handle the battery with care, as it contains acid that can cause injury.
- Wear gloves and safety glasses when working with batteries.
- Use a torque wrench to tighten the bolts and nuts securely, but avoid overtightening.
|
Conclusion: |
|
Replacing the battery in your 2011 Honda Accord is a relatively straightforward process that can be done at home with basic tools. Just remember to handle the battery with care, follow proper safety precautions, and tighten all connections securely.
|
| Q1: What type of battery does my 2011 Honda Accord use? |
A1: The 2011 Honda Accord uses a 12-volt, maintenance-free battery with a cold cranking amps (CCA) rating of 550 or higher. |
| Q2: Where is the battery located in my 2011 Honda Accord? |
A2: The battery is located in the engine compartment, on the driver's side. It is held in place by a bracket and secured with two 10mm bolts. |
| Q3: What tools do I need to replace the battery in my 2011 Honda Accord? |
A3: You will need a wrench or socket set, including a 10mm socket and a Phillips screwdriver. It is also recommended to wear protective gloves and safety glasses. |
| Q4: How do I disconnect the battery cables in my 2011 Honda Accord? |
A4: To disconnect the battery cables, loosen the nut on the cable clamp with a wrench or socket. Then, pull the cable off the terminal post. Repeat for the other cable. |
| Q5: What is the correct procedure for removing the old battery in my 2011 Honda Accord? |
A5: To remove the old battery, loosen the two 10mm bolts that hold it in place. Then, lift the battery out of the bracket and set it aside. |
| Q6: How do I install a new battery in my 2011 Honda Accord? |
A6: To install a new battery, place it in the bracket and secure it with the two 10mm bolts. Make sure they are tightened snugly. |
| Q7: What is the correct procedure for connecting the battery cables in my 2011 Honda Accord? |
A7: To connect the battery cables, place the cable on the terminal post and tighten the nut with a wrench or socket. Repeat for the other cable. |
| Q8: Do I need to reset any systems after replacing the battery in my 2011 Honda Accord? |
A8: Yes, you may need to reset some systems, such as the clock and radio presets. Consult your owner's manual for specific instructions. |
| Q9: Can I replace the battery in my 2011 Honda Accord myself? |
A9: Yes, you can replace the battery yourself with basic tools and knowledge. However, if you are not comfortable with DIY car repairs, it is recommended to seek assistance from a professional mechanic. |
| Q10: What is the average lifespan of a battery in a 2011 Honda Accord? |
A10: The average lifespan of a battery in a 2011 Honda Accord is around 5-7 years, depending on factors such as driving conditions, climate, and maintenance. |
| Rank |
Pioneers/Companies |
Description |
| 1. |
Honda Motor Co., Ltd. |
Developed the first hybrid car, Insight (1999), and popularized battery replacement for Accord models. |
| 2. |
Toshiba Corporation |
Supplied nickel-metal hydride (NiMH) batteries to Honda for the Civic Hybrid (2003) and other models. |
| 3. |
GS Yuasa International Ltd. |
Provided lithium-ion batteries for various hybrid vehicles, including the Honda Clarity Electric (2017). |
| 4. |
Johnson Controls |
Manufactured advanced lead-acid batteries for numerous automotive applications, including the Honda Accord. |
| 5. |
Exide Technologies |
Developed and supplied maintenance-free batteries to the automotive industry, including Honda models. |
| 6. |
A123 Systems |
Produced lithium-ion phosphate (LiFePO4) batteries for various hybrid vehicles, including some Honda models. |
| 7. |
Hitachi Chemical Co., Ltd. |
Supplied lead-acid and lithium-ion batteries to Honda and other automotive manufacturers. |
| 8. |
Matsushita Battery Industrial Co., Ltd. (Panasonic) |
Manufactured advanced battery technologies, including nickel-metal hydride and lithium-ion batteries for hybrid vehicles. |
| 9. |
Sanyo Electric Co., Ltd. |
Developed high-performance NiMH batteries used in various hybrid vehicles, including the Honda Civic Hybrid (2003). |
| 10. |
EnerSys |
Provided maintenance-free lead-acid and lithium-ion batteries for numerous automotive applications, including some Honda models. |
| 2011 Honda Accord Battery Replacement Guide |
| Important: Before starting, make sure you have a replacement battery that is compatible with your vehicle. The recommended battery type for the 2011 Honda Accord is a 51R or 4D. |
| Tools Needed: |
- Socket wrench or ratchet and socket
- 10mm socket
- Torx screwdriver (for some trim levels)
- Pliers or a battery terminal puller
- Memory keeper or code reader (optional)
|
| Step-by-Step Instructions: |
- Open the hood and locate the battery. It's on the driver's side, near the air intake duct.
- Disconnect the negative (black) cable from the battery post using a 10mm socket. Loosen the bolt by turning it counterclockwise, then pull the cable off the post.
- Disconnect the positive (red) cable from the battery post using a 10mm socket. Loosen the bolt by turning it counterclockwise, then pull the cable off the post.
- Remove the battery hold-down clamp using a 10mm socket. Loosen the bolt by turning it counterclockwise, then lift the clamp off the battery.
- Carefully lift the battery out of the compartment and set it aside in a safe location.
- Inspect the battery terminals and cables for any signs of damage or corrosion. Clean them as needed with a wire brush and baking soda.
- Install the new battery, making sure it's securely seated in the compartment and the hold-down clamp is tightened properly.
- Reconnect the positive (red) cable to the battery post using a 10mm socket. Tighten the bolt by turning it clockwise until snug.
- Reconnect the negative (black) cable to the battery post using a 10mm socket. Tighten the bolt by turning it clockwise until snug.
|
| Troubleshooting Tips: |
- If the battery is not holding a charge, check the alternator belt for any signs of wear or damage.
- If the battery terminals are corroded, clean them with a wire brush and baking soda before installing the new battery.
- If you're having trouble finding the battery hold-down clamp, consult your owner's manual or contact a Honda dealership for assistance.
|
|