NutriBullet Pro 900 Disassembly Repair Guide

Disassembling the NutriBullet Pro 900 Series Blender Base

If you're experiencing issues with your NutriBullet Pro 900 series blender, such as sticky or hard-to-press actuator switches, it may be due to debris or liquid accumulation in the exposed white switches. This article will guide you through the process of disassembling the blender base to clean the switches and resolve the issue.

Preparation

• Unplug the machine to ensure your safety while working on it.
• Turn the NutriBullet motor base upside down to access the screws at the bottom.

Removing the Bottom Cover

There are four screws located on the bottom of the unit. Remove these screws using a screwdriver, then grasp the bottom cover from the top and pull it out.

Removing Additional Screws and Components

• Remove three screws around the motor fan bracket.
• Remove two screws on top of the power cord guide, along with the plastic guide itself.
• The motor fan bracket should now be completely removed. Set it aside for reassembly later.

Accessing and Cleaning the Switches

Lift the power cord out of its notch in the back, then remove the plastic base by feeding the power cord through as you take it off. The piece may require cleaning using soap, water, and a soft sponge.

• Remove the metal outer sleeve on the motor housing by gently lifting it up and feeding the power cable through.
• Clean this piece thoroughly, paying attention to any areas with sticky residue or debris accumulation.

Removing Additional Components for Deep Cleaning

If necessary, remove the three white rubber covers from inside the cup by grabbing their tabs and pulling them off. This will reveal three screws underneath that need to be removed.

• Gently lift the plastic shell up and off the unit, feeding the power cord through as you go.
• This piece may also require thorough cleaning due to sticky gunk or residue clogging the switch channels.

Deep Cleaning the Switches

If the switches themselves are dirty, you may need to remove them for a deeper clean. This involves taking out two screws holding in the plastic spring clip.

• Be cautious not to damage any components during this process.
• Clean the switches and surrounding areas thoroughly before reassembling everything.

Reassembly

Follow the steps in reverse to reassemble your NutriBullet Pro 900 series blender base, ensuring that all screws and components are securely in place.

Testing Your Blender

After completing the cleaning and reassembly process, test your NutriBullet Pro 900 series blender to ensure that it is functioning properly. The actuators should engage at the same time, and none of them should feel sticky or jammed.

Tips for Maintenance and Repair

• Regularly clean your NutriBullet Pro 900 series blender to prevent debris accumulation and ensure smooth operation.
• If you experience any issues, refer to the user manual or contact customer support before attempting repairs.
• Consider purchasing spare parts for future repairs to save time and hassle.

Conclusion

By following the steps outlined in this article, you should be able to disassemble your NutriBullet Pro 900 series blender base and clean or replace any faulty components. This can help resolve common issues such as sticky or hard-to-press actuator switches, ensuring that your blender continues to function optimally.

• Torx screwdriver (T20)
• Phillips screwdriver (#2)
• Pliers
• Screw extractor (optional)

1. Unplug the NutriBullet Pro 900 from the power source to avoid any accidental starts or electrical shocks.
2. Remove the pitcher and lid from the motor base.
3. Use a Torx screwdriver (T20) to remove the screws that hold the motor base together. There are four screws in total, two on each side of the base.
4. Gently pry the motor base apart using a flathead screwdriver or a similar tool. Be careful not to damage any of the internal components.
5. Remove the circuit board and any other components that may be obstructing your view of the internal mechanisms.

• Blade Replacement: If the blades are damaged or worn out, you can replace them with a new set. Simply remove the old blades by unscrewing the retaining ring and pulling them out. Install the new blades in the reverse order.
• Bearing Replacement: If the bearings are worn out or damaged, you may need to replace them. Use a bearing puller to remove the old bearings and install new ones.
• Circuit Board Repair: If the circuit board is damaged, you may be able to repair it by replacing faulty components or re-soldering loose connections.

1. Reattach the circuit board and any other components that you removed during disassembly.
2. Reassemble the motor base by aligning the two halves and screwing them together using the Torx screws (T20).
3. Replace the pitcher and lid onto the motor base.
4. Plug in the NutriBullet Pro 900 and test it to ensure that all repairs were successful.

• Always unplug the NutriBullet Pro 900 before starting any repairs.
• Use caution when handling electrical components to avoid damage or injury.
• If you are not comfortable with DIY repairs, it is recommended that you consult a professional appliance technician.